USB DrDAQ Data Logger Specifications

DrDAQ Data Logger General Specifications
Number of channels 14
Maximum sampling rate
Block mode
USB streaming

1 MS/s#
100 kHz#
Memory depth (block mode) 16 kS#
Memory depth (USB streaming)
PicoLog
PicoScope
Using the API

1 MS#
20 MS#
unlimited

# Shared between active channels.

Oscilloscope/Spectrum Analyser Channel
Bandwidth 100 kHz
Resolution 8 bits
Input characteristics 1 MΩ
Input type Single-ended, BNC connector
Input coupling DC
Input ranges (full scale) ±1.25 V, ±2.5 V, ±5 V, ±10 V
DC accuracy ±3%
Timebases 10 µs/div to 200 s/div
Function Generator/Arbitrary Waveform Generator (AWG)
Channels 1
Connector BNC
Standard waveforms Sine, square, triangle, ramp (up/down), DC level
Function generator frequency range DC to 20 kHz
Signal amplitude ±1.5 V
Signal offset ±1.5 V
AWG buffer size 4096 samples
AWG update rate 2 MS/s (maximum)
AWG resolution 10 bits
Built–in Sensors/Outputs
Channel Range Resolution Accuracy
Sound waveform ±100 ±0.2 not calibrated
Sound level 55 to 100 dBA 1 dBA 5 dBA
Temperature -10 to +70 °C 0.1 °C  @ 25 °C 2 °C  @ 25 °C
Light 0 to 100 0.1 not calibrated
RGB LED 16.7 million colours 8 bit x 3 not applicable
Analogue Inputs
Type Connector Range Resolution Accuracy
pH BNC 0 to 14 pH 0.02 pH Sensor calibration dependent
Redox/ORP BNC (shared with pH) ±2000 mV  @ 1012 Ω 1.2 mV Sensor calibration dependent
Resistance Screw terminal 0 to 1 MΩ 250 Ω @ 10 k 5%
External sensors 3 x FCC68 4/4 Measure 0 to 2.5 V
(Also supply power to external sensors and identify sensor type via ID resistor.)
1 mV 1%
Configurable Digital IO
Channels 4
Connector type Screw terminals
Input characteristics 0 to 5 V (Low:0- 0.8 V, High: 2 -5.5 V)
TTL compatible
Output characteristics 3.3 V, 2.2 kΩ output impedance
PWM output
Period
Pulse
Resolution

<65535 µs
<65535 µs
1 µs
Available on 2 Digital IO channels
Pulse counting Up to 65535 counts @ 500 kHz
Available on 2 Digital IO channels
PC Requirements
Minimum Processor: 1 GHz
Memory: 512 MiB
Free disk space*: 32–bit: 600 MB, 64–bit: 1.5 GB
Operating system: 32– or 64–bit edition of Microsoft Windows XP (SP3), Vista, Windows 7 or Windows 8#
Ports: USB 2.0 compliant port
Recommended Processor: 1 GHz
Memory: 512 MiB
Free disk space*: 32–bit: 850 MB, 64–bit: 2 GB
Operating system: 32– or 64–bit edition of Microsoft Windows XP (SP3), Vista, Windows 7 or Windows 8 (not Windows RT)
Ports: USB 2.0 or 3.0 compliant port
  • # Not Windows RT.
  • * The PicoScope software does not use all the disk space specified in the table.
    The free space is required to make Windows run efficiently.
Physical Properties
Dimensions 77 x 70 x 23 mm  (approx 3 x 2.7 x 0.9 in)
(includes BNC connectors)
Weight 60 g  (approx 2.1 oz)
Software
PicoLog for Windows PicoLog data acquisition software can collect up to 1 million samples. Features include:
Multiple views - view data as a graph, spreadsheet or text
Parameter scaling - convert raw data into standard engineering units
Math functions - use mathematical equations to calculate additional parameters
Alarm limits - program an alert if a parameter goes out of a specified range
IP networking - transfer measurements via a LAN or over the Internet
Full details on PicoLog
PicoScope 6 for Windows PicoScope 6 is your complete test and measurement lab in one application. Features include:
Capture modes - oscilloscope, spectrum and persistence modes
Channel maths - calculate the sum, difference, product, inverse or create your own custom function using standard arithmetic, exponential and trigonometric functions
Automated measurements
Scope mode: AC RMS, cycle time, DC average, duty cycle, falling rate, fall time, frequency, high pulse width, low pulse width, maximum, minimum, peak-to-peak, rise time and rising rate
Spectrum mode: frequency at peak, amplitude at peak, total power, total harmonic distortion (THD), total harmonic distortion plus noise (THD+N), spurious-free dynamic range (SFDR), signal+noise+distortion to signal+noise ratio (SINAD), signal to noise ratio (SNR) and intermodulation distortion (IMD)
Export data formats - Comma separated values (CSV), tab delimited (TXT), windows bitmap (BMP), graphics interchange format (GIF), portable network graphics (PNG), MATLAB 4 format (MAT)
Full details on PicoScope 6
Software development kit A growing collection of drivers and example code for various programming languages including: C, C++, Excel and LabVIEW.
Language Support
Software
PicoLog

PicoScope 6

Full support for English, French and German; menus only for Italian, Spanish and Swedish
Full support for English, French, Italian, German and Spanish. Menus and dialogs only for Dutch, Hungarian and Simplified Chinese.
Documentation
User’s guide
Programmer’s guide

English
English
General
Data sheet English 中文 (简体), Deutsch, Español, Français, Italiano
Additional hardware (supplied) USB 2.0 cable, user manuals, software CD–ROM
PC interface USB 2.0 (USB 1.1 compatible)
Power requirements Powered from USB port
Compliance European EMC and LVD standards
FCC Rules Part 15 Class A
RoHS compliant
Total Satisfaction Guarantee In the event that this product does not fully meet your requirements you can return it for an exchange or refund. To claim, the product must be returned in good condition within 14 days.
Warranty 5 years
Price: DrDAQ Data Logger
In stock
US$163.35
Price: DrDAQ Kit
(comprising DrDAQ, 2 temperature sensors, 1 pH sensor, 1 humidity sensor and 1 oscilloscope probe.)
Dispatched within 1 week

US$361.35